Fieldserver FCI 7100 Series Manual de usuario descargar pdf (Pagina 16)

FS-8700-112 Gamewell-FCI 7100 Driver Manual Page 16 of 20

FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com

Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: support@fieldserver.com

Message

Description

FCI7100:#13a Err. Diagnostic 1);

Take a log. Try and repeat the event that

caused the message to be printed. Then

contact tech support.

FCI7100:#13b Err. Diagnostic 2);

FCI7100:#13c Err. Diagnostic 3);

FCI7100:#14 Err. <%s> file not found., md->mapdesc_name ) ;

If this error is repeated often it is possible that

a FCI firmware update as made the driver

unusable. Take a log and contact tech

support.

FCI7100:#15 Err. Event Type=<%s> Not recognized." , drv_bd-

>event_desc )

FCI7100:#16 Err. Point Type='%c'(%#x) Not recognized. ,

drv_bd->point_identifier[0] , drv_bd->point_identifier[0] ) ;

FCI7100:#17 Err. Loop=%d < 1. Rejected. , drv_bd->loop )

This message is printed if a byte in a message

has been corrupted. If you notice it more than

once then take a log and contact tech support.

FCI7100:#18 Err. Loop Type='%c'(%#x) Not recognized. , drv_bd-

>point_identifier[2] , drv_bd->point_identifier[2] )

If this error is repeated often it is possible that

a FCI firmware update as made the driver

unusable. Take a log and contact tech support.

FCI7100:#19 Err. Relay=%d < 1. Rejected. , drv_bd->relay

This message is printed if a byte in a message

has been corrupted. If you notice it more than

once then take a log and contact tech support.

FCI7100:#20 Err. Zone=%d < 1. Rejected. , drv_bd->zone"

FCI7100:#21 Err. Point Type not recognized

Valid Point Types are listed in section 5.3.2

FCI7100:#22 Err. Undefined Point Type"

FCI7100:#23 Err. Event Type not recognized

Valid Event Types are listed in section

5.3.2Error! Bookmark not defined.

FCI7100:#24 Err. Undefined Event Type

FCI7100:#25a Err. Address+Length>99. Length Truncated

The maximum value for a sensor/module is

99. The combination of address and length

specified produce a number > 99Error!

Bookmark not defined.

FCI7100:#25b Err. Address+Length>99. Length Truncated

FCI7100:#26 Err. Invalid Module number. Expected 1..99

Correct the configuration fileError! Bookmark

not defined.

FCI7100:#27a Err. Invalid Loop number. Expected 1..10

FCI7100:#27b Err. Invalid Loop number. Expected 1..10

FCI7100:#27c Err. Invalid Loop number. Expected 1..10

FCI7100:#28 Err. Invalid Sensor number. Expected 1..99

Correct the configuration file.

Error!

Bookmark not defined.

FCI7100:#29 Err. Invalid Zone number. Expected 1..255

FCI7100:#30 Err. Invalid Relay number. Expected 1..255

FCI7100:#31 Err. Point Type Invalid.

Valid Point Types are listed in Section

5.3.2Error! Bookmark not defined.

FCI7100:#32 Err. No MD Length. Default to 1

Specify the 'length' of each Map Descriptor.

Refer to Section 5.3.2Error! Bookmark not

defined.

FCI7100:#33 Err. Driver cant poll or write.

The driver can only listen passively for

message from the panel. Remove any active

Map Descriptors from the configuration file.

Correct the configuration file, download to the FieldServer and restart the FieldServer for the changes to take effect.

1 2 ... 11 12 13 14 15 16 17 18 19 20

Comentarios a estos manuales

Sin comentarios

Fieldserver FCI 7100 Series Manual de usuario Pagina 16

Comentarios a estos manuales

Relacionado con productos y manuales para Hardware Fieldserver FCI 7100 Series